Discounted Genuine Brembo front rotors 355mm

[FLOORED]

I have been offered some Genuine Brembo Xdrilled and slotted 355mm front rotors that will fit all 4 or 6 piston front Brembo calipers for AU11 AU111 BA BF and FG fords for the very low clearance price of $600 a pair. There is very limited pairs available so it is first in first served thankyou and i apologize now if you miss out as these prices are very cheap.Pick up is available or we can freight Australia wide and the weight is about 25kgs a pair.
The rotors will have to be paid for before we ship and i need a few orders to get the stock rolling thanks.

355mm x 32mm Genuine Brembo front rotors $600 a pair one off limited stock.

Please put your name here and qty.

[Blem]

Hi Floored
Was going to order some dba5000 rotors from you but can't go past this offer.
Put me down for a pair & some pads to 5152.
Which pads do you recommend for general duties with a few track days ?

[FLOORED]

Originally Posted by Blem

Hi Floored
Was going to order some dba5000 rotors from you but can't go past this offer.
Put me down for a pair & some pads to 5152.
Which pads do you recommend for general duties with a few track days ?

The 5000's are a better choice but you can always get them next time.Did you have the 4 or 6 piston front Brembo's? Ferodo DS2500 pads would be best choice or we have some new pads called Bremtec which are a bit cheaper.

[Ride]

What would be the cost of dba5000 replacement outers in comparison? Mine are due soon

[Whitey-AMG]

Any pics of these brembo rotors. Is there a genuine p/n available. What is the performance and longevity like.

[FLOORED]

Originally Posted by Ride

What would be the cost of dba5000 replacement outers in comparison? Mine are due soon

In the T3 slotted they are $330 each at the moment

Originally Posted by ESP

Any pics of these brembo rotors. Is there a genuine p/n available. What is the performance and longevity like.

They are the Genuine factory Brembo 355mm rotor that is crossdrilled and has the 3 slots on them which is the main replacement rotor these days as they have discontinued the earlier BA xdrilled only rotors although they are still found.
Performance and longevity depends on what pads you fit and how you drive and treat the vehicle.
Have you not had the genuine rotors on your Brembo before? I find they are a little softer than a DBA rotor if that makes sense.

[M&Ms]

Any specials going on for brembo genuine rear rotors to suit 6/4 brembo brakes (330 x 28)??

[FLOORED]

Originally Posted by M&Ms

Any specials going on for brembo genuine rear rotors to suit 6/4 brembo brakes (330 x 28)??

$430 each but not sure if that is a good price or not i actually haven't sold any for years.

[Blem]

Pm received & payment processed.
Thanks.
Brembo deal to good to go past.

[FLOORED]

Originally Posted by Blem

Pm received & payment processed.
Thanks.
Brembo deal to good to go past.

Don't forget to send me all your delivery and contact details thanks.

[Dman4.0]

Is there any rotor around the same price range that does a better job? Ive only just purchased Brembo's and havn't really looked at replacement rotors yet. Cheers.

[FLOORED]

Originally Posted by Dman4.0

Is there any rotor around the same price range that does a better job? Ive only just purchased Brembo's and havn't really looked at replacement rotors yet. Cheers.

The DBA T3 slotted rotors are about this price or cheaper at any given time but also the correct pad choice also makes a great stopping combination.

[HEMI POWER]

This Deal still on

[Whitey-AMG]

Originally Posted by FLOORED

The DBA T3 slotted rotors are about this price or cheaper at any given time but also the correct pad choice also makes a great stopping combination.

Is that the T3 DBA 42102 rotor ?
Are they around 600 for the pair or cheaper.
Are they a better rotor than the brembo unit.
Curious here as I too will need some rotors soon.

[EASYBOSS]

Hi Matt

Are these rotors that same as fitted to an F6X with 6 pot brembo's

[Blem]

Thanks Matt.

Front rotors & pads landed today.

Pls feel free to call me Blem, Todd or Prue.

Gotta love good book/file keeping & RETURN custom

Ps... still to fit those rear pads that I had thrown in to help make the initial (visa) purchase worthwhile.

All good now I hope mate

[FLOORED]

Originally Posted by Blem

Thanks Matt.

Front rotors & pads landed today.

Pls feel free to call me Blem, Todd or Prue.

Gotta love good book/file keeping & RETURN custom

Ps... still to fit those rear pads that I had thrown in to help make the initial (visa) purchase worthwhile.

All good now I hope mate

Ha Ha Ha i thought you would like that. I think i had that name listed from before as from memory you were going away and they were home to sign for the goods. A very good return customer you are and you are listed in the Ford Forum family.

Originally Posted by Gambit

Matt,

Do you know if there's any difference in face height/mounting depth or rotor size between these rotors & Dba 5000? Reason I ask is I had the 5000 series on my pursuit 250 with the twin piston setup & the rotors inner face was the same size as the outer & caught on the mounting bolts. The original rotors had a smaller inner face so cleared the bolts.

Just curious for when I need replacements for my brembos to grab a set of these or go the 5000 which I'd rather.

Cheers

Nathan

Ok i understand everything but then you through in the twin piston caliper and now i am confused.
Any DBA 5000 rotor you buy is a direct fit for the one piece it replaces. If you have the 4 piston Brembo front rotor i may suggest you could have a EVO or STI brake pad fitted as these have a deeper profile with more pad material so they hang lower and these pads (backing plate) do foul on the bolts and nuts that mount the alloy hat to the rotor. They won't on the 1 piece as they just overhang. To follow up on this you can trace the brake pad and put some measurements down and either upload the photo or email it to me to check.

Originally Posted by ESP

Is that the T3 DBA 42102 rotor ?
Are they around 600 for the pair or cheaper.
Are they a better rotor than the brembo unit.
Curious here as I too will need some rotors soon.

The DBA T3 Slotted rotors are on special for $550 a pair at the moment until stock is sold and again these are also limited.
DBA T3 i feel has the edge but the Brembo rotor is a very good rotor and at a very good price if you want too retain that factory look.

Originally Posted by EASYBOSS

Hi Matt

Are these rotors that same as fitted to an F6X with 6 pot brembo's

They are not the same style as the F6X had fitted as they had a plain rotor but these xdrilled will fit and can be used.

[FLOORED]

all sold thankyou

[Blem]

That was a sneeze & they are gone.
Great pricing & as always great service by the team at RBS.
Is it possible to get on a mailing list of specials ?

[FLOORED]

Originally Posted by Blem

That was a sneeze & they are gone.
Great pricing & as always great service by the team at RBS.
Is it possible to get on a mailing list of specials ?

Please don't get technical with me BLEM . This mailing list may happen one day so don't give up.

[FLOORED]

Originally Posted by Blem

That was a sneeze & they are gone.
Great pricing & as always great service by the team at RBS.
Is it possible to get on a mailing list of specials ?

Here is your chance
I have been contacted this morning and been told that they will supply me another 5 pairs for us at the same price so get in quick.
I am trying to get more qty's as you read this.

[grandpa_spec_F6]

I'm down for a pair

[FLOORED]

Have a new batch of these rotors available at $600 a pair.

[AlfaRomeoGTV6]

Originally Posted by FLOORED

Have a new batch of these rotors available at $600 a pair.

G'day Matt, Is this deal currently available ? Cheers mate

[FLOORED]

Originally Posted by AlfaRomeoGTV6

G'day Matt, Is this deal currently available ? Cheers mate

I have more stock hopefully coming in at the end of next week and then i can do the deal for you.Best if you want them to get them all paid up to secure them i have 5 pair coming and possily these are the last batch at this price.

[grandpa_spec_F6]

Finally bedded mine in with the Ceramic pads and my GOD is it nice to have decent braking again... and NO BLOODY BLACK DUST! Cleaned the wheels in about 10 seconds compared to the stock pads.

Thanks again Matt!

[Black F6]

Hi Matt,

I have a FG F6 and need to replace the pads and rotors

4 pot front and PBR rear, do a bit of drag work and occasional track days, could you give me a qoute for front and back please

[FLOORED]

Originally Posted by Black F6

Hi Matt,

I have a FG F6 and need to replace the pads and rotors

4 pot front and PBR rear, do a bit of drag work and occasional track days, could you give me a qoute for front and back please

I have genuine front and rear rotors here for $1030 or the DBA T3 Slotted for $980 or 2 piece DBA T3 front and 1 piece rear T3 for $1420.
Brake pads you could run the Ferodo DS2500 on the front and the DS Performance for the rear at $460 or the new Bremtec evolve pads for $350.00.
Or if you have some combo in mind let me know and i will quote it.

[Black F6]

Originally Posted by FLOORED

I have genuine front and rear rotors here for $1030 or the DBA T3 Slotted for $980 or 2 piece DBA T3 front and 1 piece rear T3 for $1420.
Brake pads you could run the Ferodo DS2500 on the front and the DS Performance for the rear at $460 or the new Bremtec evolve pads for $350.00.
Or if you have some combo in mind let me know and i will quote it.

Hi Matt,

Will take the genuine front and rears, also the bremtec pads

Can you invoice Scott Dawes and email to [email protected]

Cheers
Scott

[FLOORED]

Originally Posted by Black F6

Hi Matt,

Will take the genuine front and rears, also the bremtec pads

Can you invoice Scott Dawes and email to [email protected]

Cheers
Scott

Hi mate are we freighting this too you or are you picking up ? If picking up then come through and pay then but if freighting it i will need a postcode to quotet the freight thanks Scott.